View MC9S08SE8_4824473.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Freescale Semiconductor Data Sheet: Technical Data
Document Number: MC9S08SE8 Rev. 3, 4/2009
MC9S08SE8
TBD MC9S08SE8 Series
Covers:
Features: * 8-Bit HCS08 Central Processor Unit (CPU) - 20 MHz HCS08 CPU (central processor unit) - 10 MHz internal bus frequency - HC08 instruction set with added BGND - Support for up to 32 interrupt/reset sources * On-Chip Memory - Up to 8 KB of on-chip in-circuit programmable flash memory with block protection and security options - Up to 512 bytes of on-chip RAM * Power-Saving Modes - Wait plus two stops * Clock Source Options - Oscillator (XOSC) -- Loop-control Pierce oscillator; crystal or ceramic resonator range of 31.25 kHz to 38.4 kHz or 1 MHz to 16 MHz - Internal Clock Source (ICS) -- Internal clock source module containing a frequency-locked-loop (FLL) controlled by internal or external reference; precision trimming of internal reference allows 0.2% resolution and 2% deviation over temperature and voltage; supports bus frequencies from 1 MHz to 10 MHz. * System Protection - Optional computer operating properly (COP) reset with option to run from independent 1 kHz internal clock source or the bus clock - Low voltage detection - Illegal opcode detection with reset - Illegal address detection with reset * Development Support - Single-wire background debug interface - Breakpoint capability to allow single breakpoint setting during in-circuit debugging * Peripherals
28-Pin SOIC Case 751F 16-Pin TSSOP Case 948F-01
MC9S08SE8 MC9S08SE4
28-Pin PDIP Case 710-02
- SCI -- Full duplex non-return to zero (NRZ); LIN master extended break generation; LIN slave extended break detection; wakeup on active edge - ADC -- 10-channel, 10-bit resolution; 2.5 s conversion time; automatic compare function; 1.7 mV/C temperature sensor; internal bandgap reference channel; runs in stop3 - TPMx -- One 2-channel (TPM1) and one 1-channel (TPM2) 16-bit timer/pulse-width modulator (TPM) modules; selectable input capture, output compare, and edge-aligned PWM capability on each channel; timer module may be configured for buffered, centered PWM (CPWM) on all channels - KBI -- 8-pin keyboard interrupt module - RTC -- Real-time counter with binary- or decimal-based prescaler * Input/Output - Software selectable pullups on ports when used as inputs - Software selectable slew rate control on ports when used as outputs - Software selectable drive strength on ports when used as outputs - Master reset pin and power-on reset (POR) - Internal pullup on RESET, IRQ, and BKGD/MS pins to reduce customer system cost * Package Options - 28-pin PDIP - 28-pin SOIC - 16-pin TSSOP
This document contains information on a product under development. Freescale reserves the right to change or discontinue this product without notice. (c) Freescale Semiconductor, Inc., 2008-2009. All rights reserved.
Table of Contents
1 2 3 MCU Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 3.1 Parameter Classification . . . . . . . . . . . . . . . . . . . . . . . . .6 3.2 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . .6 3.3 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .7 3.4 ESD Protection and Latch-Up Immunity . . . . . . . . . . . . .8 3.5 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3.6 Supply Current Characteristics . . . . . . . . . . . . . . . . . . .15 3.7 External Oscillator (XOSC) Characteristics . . . . . . . . .19 3.8 Internal Clock Source (ICS) Characteristics . . . . . . . . 3.9 ADC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10.1 Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . 3.10.2 TPM/MTIM Module Timing . . . . . . . . . . . . . . . . 3.11 Flash Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Mechanical Drawings. . . . . . . . . . . . . . . . . . . . . . . . . . 20 22 25 25 26 27 27 28 28
4
Revision History
To provide the most up-to-date information, the revision of our documents on the World Wide Web will be the most current. Your printed copy may be an earlier revision. To verify you have the latest information available, refer to:
http://freescale.com/
The following revision history table summarizes changes contained in this document.
Revision 1 2 3 Date 10/8/2008 1/16/2009 4/7/2009 Initial public released. In Table 8, added the Max. of S2IDD and S3IDD in 0-105 C; changed the Max. of S2IDD and S3IDD in 0-85 C; changed the typical of S2IDD and S3IDD; changed the S23IDDRTI to P. Added |IOZTOT| in the Table 7. Changed VDDAD to VDDA, VSSAD to VSSA. Updated Table 9, Table 10, Table 11, and Table 12. Updated Figure 13 and Figure 14. Description of Changes
Related Documentation
Find the most current versions of all documents at: http://www.freescale.com
Reference Manual
(MC9S08SE8RM) Contains extensive product information including modes of operation, memory, resets and interrupts, register definition, port pins, CPU, and all module information. MC9S08SE8 Series MCU Data Sheet, Rev. 3
2
Freescale Semiconductor
MCU Block Diagram
1
MCU Block Diagram
The block diagram, Figure 1, shows the structure of the MC9S08SE8 series MCUs.
HCS08 CORE CPU BDC
BKGD/MS
DEBUG MODULE (DBG)
HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT COP IRQ LVD REAL-TIME COUNTER (RTC) PTA7/TPM1CH1/ADP5 PTA6/TPM1CH0/ADP4 PTA5/IRQ/TCLK/RESET PTA4/BKGD/MS PTA3/KBIP3/ADP3 PTA2/KBIP2/ADP2 PTA1/KBIP1/TPM1CH1/ADP1 PTA0/KBIP0/TPM1CH0/ADP0 PTB7/EXTAL PTB6/XTAL PTB5 PORT B 1-CHANNEL TIMER/PWM MODULE (TPM2) EXTAL XTAL TCLK TPM2CH0 PTB4/TPM2CH0 PTB3/KBIP7/ADP9 PTB2/KBIP6/ADP8 PTB1/KBIP5/TxD/ADP7 PTB0/KBIP4/RxD/ADP6
IRQ
USER FLASH (MC9S08SE8 = 8192 BYTES) (MC9S08SE4 = 4096 BYTES) USER RAM (MC9S08SE8 = 512 BYTES) (MC9S08SE4 = 256 BYTES) 20 MHz INTERNAL CLOCK SOURCE (ICS) LOW-POWER OSCILLATOR 31.25 kHz to 38.4 kHz 1 MHz to 16 MHz (XOSC) VSS
2-CHANNEL TIMER/PWM MODULE (TPM1)
TCLK TPM1CH1-TPM1CH0
SERIAL COMMUNICATIONS INTERFACE MODULE (SCI)
RxD TxD
PORT A
KEYBOARD INTERRUPT MODULE (KBI)
KBIP7-KBIP0
PTC7 VOLTAGE REGULATOR PORT C VSSA VDDA VREFL VREFH PTC6 PTC5 PTC4 PTC3 PTC2 PTC1 PTC0 10-CHANNEL, 10-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) ADP9-ADP0
VDD VSSA/VREFL VDDA/VREFH
pins not available on 16-pin package Notes: When PTA4 is configured as BKGD, pin is bi-directional. For the 16-pin package: VSSA/VREFL and VDDA/VREFH are double bonded to VSS and VDD respectively.
Figure 1. MC9S08SE8 Series Block Diagram
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 3
Pin Assignments
2
Pin Assignments
Table 1. Pin Availability by Package Pin-Count
Pin Number (Package) 28 (SOIC/PDIP) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
1
This chapter shows the pin assignments in the packages available for the MC9S08SE8 series.
<-- Lowest Port Pin PTC5 PTC4 PTA5 PTA4 IRQ Alt 1
Priority
--> Highest Alt 2 Alt 3
16 (TSSOP) -- -- 1 2 3 -- -- 4 5 6 7 8 -- -- -- -- 9 10 11 12 -- -- 13 14 15 16 -- --
TCLK BKGD VDDA VSSA
RESET MS VDD VREFH VREFL VSS
PTB7 PTB6 PTB5 PTB4 PTC3 PTC2 PTC1 PTC0 PTB3 PTB2 PTB1 PTB0 PTA7 PTA6 PTA3 PTA2 PTA1 PTA0 PTC7 PTC6
EXTAL XTAL TPM2CH0
KBIP7 KBIP6 KBIP5 KBIP4 TxD RxD TPM1CH1 KBIP3 KBIP2 KBIP1 KBIP0 TPM1CH1
1 1
ADP9 ADP8 ADP7 ADP6 ADP5 ADP4 ADP3 ADP2 ADP1 ADP0 TPM1CH01
TPM1CH01
TPM1 pins can be remapped to PTA7, PTA6 and PTA1,PTA0
MC9S08SE8 Series MCU Data Sheet, Rev. 3 4 Freescale Semiconductor
Pin Assignments
PTC5 PTC4 PTA5/IRQ/TCLK/RESET PTA4/BKGD/MS VDD VDDA/VREFH VSSA/VREFL VSS PTB7/EXTAL PTB6/XTAL PTB5 PTB4/TPM2CH0 PTC3 PTC2
1 2 3 4 5 6 7 8 9 10 11 12 13 14
28 27 26 25 24 23 22 21 20 19 18 17 16 15
PTC6 PTC7 PTA0/KBIP0/TPM1CH0/ADP0 PTA1/KBIP1/TPM1CH1/ADP1 PTA2/KBIP2/ADP2 PTA3/KBIP3/ADP3 PTA6/TPM1CH0/ADP4 PTA7/TPM1CH1/ADP5 PTB0/KBIP4/RxD/ADP6 PTB1/KBIP5/TxD/ADP7 PTB2/KBIP6/ADP8 PTB3/KBIP7/ADP9 PTC0 PTC1
Pins in bold are lost in the next lower pin count package.
Figure 2. MC9S08SE8 Series in 28-Pin PDIP/SOIC Package
PTA5/IRQ/TCLK/RESET PTA4/BKGD/MS VDD VSS PTB7/EXTAL PTB6/XTAL PTB5 PTB4/TPM2CH0
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
PTA0/KBIP0/TPM1CH0/ADP0 PTA1/KBIP1/TPM1CH1/ADP1 PTA2/KBIP2/ADP2 PTA3/KBIP3/ADP3 PTB0/KBIP4/RxD/ADP6 PTB1/KBIP5/TxD/ADP7 PTB2/KBIP6/ADP8 PTB3/KBIP7/ADP9
Figure 3. MC9S08SE8 in 16-Pin TSSOP Package
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 5
Electrical Characteristics
3
3.1
Electrical Characteristics
Parameter Classification
This chapter contains electrical and timing specifications.
The electrical parameters shown in this supplement are guaranteed by various methods. To give the customer a better understanding, the following classification is used and the parameters are tagged accordingly in the tables where appropriate:
Table 2. Parameter Classifications
P C Those parameters are guaranteed during production testing on each individual device. Those parameters are achieved by the design characterization by measuring a statistically relevant sample size across process variations. Those parameters are achieved by design characterization on a small sample size from typical devices under typical conditions unless otherwise noted. All values shown in the typical column are within this category. Those parameters are derived mainly from simulations.
T D
NOTE The classification is shown in the column labeled "C" in the parameter tables where appropriate.
3.2
Absolute Maximum Ratings
Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the limits specified in Table 3 may affect device reliability or cause permanent damage to the device. For functional operating conditions, refer to the remaining tables in this section. This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, it is advised that normal precautions be taken to avoid application of any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate logic voltage level (for instance, either VSS or VDD) or the programmable pull-up resistor associated with the pin is enabled.
MC9S08SE8 Series MCU Data Sheet, Rev. 3 6 Freescale Semiconductor
Electrical Characteristics
Table 3. Absolute Maximum Ratings
Rating Supply voltage Maximum current into VDD Digital input voltage Instantaneous maximum current Single pin limit (applies to all port pins)1, 2, 3 Storage temperature range
1
Symbol VDD IDD VIn ID Tstg
Value -0.3 to 5.8 120 -0.3 to VDD + 0.3 25 -55 to 150
Unit V mA V mA C
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive (VDD) and negative (VSS) clamp voltages, then use the larger of the two resistance values. 2 All functional non-supply pins are internally clamped to VSS and VDD. 3 Power supply must maintain regulation within operating V DD range during instantaneous and operating maximum current conditions. If positive injection current (VIn > VDD) is greater than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if the clock rate is very low (which would reduce overall power consumption).
3.3
Thermal Characteristics
This section provides information about operating temperature range, power dissipation, and package thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in on-chip logic and voltage regulator circuits, and it is user-determined rather than being controlled by the MCU design. To take PI/O into account in power calculations, determine the difference between actual pin voltage and VSS or VDD and multiply by the pin current for each I/O pin. Except in cases of unusually high pin current (heavy loads), the difference between pin voltage and VSS or VDD will be very small.
Table 4. Thermal Characteristics
Rating Operating temperature range (packaged) C V M Maximum junction temperature 28-pin SOIC Thermal resistance single-layer board 28-pin PDIP 16-pin TSSOP 28-pin SOIC Thermal resistance four-layer board 28-pin PDIP 16-pin TSSOP JA TA TJM Symbol Value TL to TH -40 to 85 -40 to 105 -40 to 125 135 70 68 129 48 49 85 C/W C/W Unit
C C
The average chip-junction temperature (TJ) in C can be obtained from:
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 7
Electrical Characteristics
TJ = TA + (PD x JA)
Eqn. 1
where: TA = Ambient temperature, C JA = Package thermal resistance, junction-to-ambient, C/W PD = Pint + PI/O Pint = IDD x VDD, Watts -- chip internal power PI/O = Power dissipation on input and output pins -- user-determined For most applications, PI/O << Pint and can be neglected. An approximate relationship between PD and TJ (if PI/O is neglected) is:
PD = K / (TJ + 273C) Eqn. 2
Solving Equation 1 and Equation 2 for K gives:
K = PD x (TA + 273C) + JA x (PD)2 Eqn. 3
where K is a constant pertaining to the particular part. K can be determined from Equation 3 by measuring PD (at equilibrium) for a known TA. Using this value of K, the values of PD and TJ can be obtained by solving Equation 1 and Equation 2 iteratively for any value of TA.
3.4
ESD Protection and Latch-Up Immunity
Although damage from electrostatic discharge (ESD) is much less common on these devices than on early CMOS circuits, normal handling precautions should be used to avoid exposure to static discharge. Qualification tests are performed to ensure that these devices can withstand exposure to reasonable levels of static without suffering any permanent damage. During the device qualification ESD stresses were performed for the human body model (HBM), the machine model (MM) and the charge device model (CDM). A device is defined as a failure if after exposure to ESD pulses the device no longer meets the device specification. Complete DC parametric and functional testing is performed per the applicable device specification at room temperature followed by hot temperature, unless specified otherwise in the device specification.
Table 5. ESD and Latch-up Test Conditions
Model Human body Description Series resistance Storage capacitance Number of pulses per pin Series resistance Machine Storage capacitance Number of pulses per pin Symbol R1 C -- R1 C -- Value 1500 100 3 0 200 3 Unit pF -- pF --
MC9S08SE8 Series MCU Data Sheet, Rev. 3 8 Freescale Semiconductor
Electrical Characteristics
Table 5. ESD and Latch-up Test Conditions (continued)
Model Latch-up Maximum input voltage limit -- 7.5 V Description Minimum input voltage limit Symbol -- Value -2.5 Unit V
Table 6. ESD and Latch-up Protection Characteristics
No. 1 2 3 4
1
Rating1 Human body model (HBM) Machine model (MM) Charge device model (CDM) Latch-up current at TA = 125 C
Symbol VHBM VMM VCDM ILAT
Min 2000 200 500 100
Max -- -- -- --
Unit V V V mA
Parameter is achieved by design characterization on a small sample size from typical devices under typical conditions unless otherwise noted.
3.5
DC Characteristics
Table 7. DC Characteristics
Num C 1 -- Operating voltage Output high voltage -- Low drive (PTxDSn = 0) 5 V, ILoad = -2 mA 3 V, ILoad = -0.6 mA 5 V, ILoad = -0.4 mA 3 V, ILoad = -0.24 mA Output high voltage -- High drive (PTxDSn = 1) 5 V, ILoad = -10 mA P 3 V, ILoad = -3 mA 5 V, ILoad = -2 mA 3 V, ILoad = -0.4 mA Output low voltage -- Low drive (PTxDSn = 0) 5 V, ILoad = 2 mA 3 V, ILoad = 0.6 mA 5 V, ILoad = 0.4 mA 3 V, ILoad = 0.24 mA Output low voltage -- High drive (PTxDSn = 1) 5 V, ILoad = 10 mA P 3 V, ILoad = 3 mA 5 V, ILoad = 2 mA 3 V, ILoad = 0.4 mA P Output high current -- Max total IOH for all ports 5V 3V Parameter Symbol -- Min 2.7 VDD - 1.5 VDD - 1.5 VDD - 0.8 VDD - 0.8 VDD - 1.5 VDD - 1.5 VDD - 0.8 VDD - 0.8 1.5 1.5 0.8 0.8 1.5 1.5 0.8 0.8 IOHT -- -- Typical1 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Max 5.5 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 100 60 mA Unit V
This section includes information about power supply requirements and I/O pin characteristics.
VOH
V
2
VOL
V
3
4
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 9
Electrical Characteristics
Table 7. DC Characteristics (continued)
Num C 5 6 7 8 9 10 11 12 13 P Parameter Output low current -- Max total IOL for all ports 5V 3V Symbol IOLT VIH VIL Vhys
2
Min -- -- 0.65 x VDD -- 0.06 x VDD -- -- -- 20 20
Typical1 -- -- -- -- -- 0.1 0.1 -- 45 45
Max 100 60 -- 0.35 x VDD -- 1 1 2 65 65
Unit mA
P Input high voltage; all digital inputs P Input low voltage; all digital inputs P Input hysteresis; all digital inputs C Input leakage current; input only pins P High impedance (off-state) leakage current2 C
V mV A A A k k
|IIn| |IOZ|
Total leakage combined for all inputs and Hi-Z pins |IOZTOT| -- All input only and I/O2 RPU RPD IIC CIn VRAM VPOR tPOR VLVD1
P Internal pullup resistors3 P Internal pulldown resistors4 DC injection current VIN < VSS, VIN > VDD D Single pin limit Total MCU limit, includes sum of all stressed pins C Input capacitance; all non-supply pins C RAM retention voltage P POR re-arm voltage D POR re-arm time Low-voltage detection threshold -- high range VDD falling VDD rising Low-voltage detection threshold -- low range VDD falling VDD rising Low-voltage warning threshold -- high range 1 VDD falling VDD rising Low-voltage warning threshold -- high range 0 VDD falling VDD rising Low-voltage warning threshold low range 1 VDD falling VDD rising Low-voltage warning threshold -- low range 0 VDD falling VDD rising
8 5, 6, 7
14
-0.2 -5 -- 0.6 0.9 10
-- -- -- 1.0 1.4 --
0.2 5 8 -- 2.0 --
mA
15 16 17 18
pF V V s
19
P
3.9 4.0
4.0 4.1
4.1 4.2
V
20
P
VLVD0
2.48 2.54
2.56 2.62
2.64 2.70
V
21
C
VLVW3
4.5 4.6
4.6 4.7
4.7 4.8
V
22
P
VLVW2
4.2 4.3
4.3 4.4
4.4 4.5
V
23
P
VLVW1
2.84 2.90
2.92 2.98
3.00 3.06
V
24
C
VLVW0
2.66 2.72
2.74 2.80
2.82 2.88
V
MC9S08SE8 Series MCU Data Sheet, Rev. 3 10 Freescale Semiconductor
Electrical Characteristics
Table 7. DC Characteristics (continued)
Num C 25 26
1 2 3 4 5 6 7
Parameter Low-voltage inhibit reset/recover hysteresis 5V 3V
Symbol Vhys VBG
Min -- -- 1.18
Typical1 100 60 1.20
Max -- -- 1.21
Unit mV V
T P Bandgap voltage reference9
8 9
Typical values are measured at 25 C. Characterized, not tested. Measured with VIn = VDD or VSS. Measured with VIn = VSS. Measured with VIn = VDD. All functional non-supply pins are internally clamped to VSS and VDD. Input must be current-limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then use the larger of the two values. Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current conditions. If positive injection current (VIn > VDD) is greater than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if clock rate is very low (which would reduce overall power consumption). Maximum is highest voltage that POR is guaranteed. Factory trimmed at VDD = 5.0 V, Temp = 25 C.
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 11
Electrical Characteristics
VOL vs IOL at VDD = 5.0 V, High Drive
700 -40C 600 500 0C 25C 70C 95C 125C 135C
VDD/mV
400 300 200 100 0 1 1.5 2 2.5 3 9 9.5 10 10.5 11
IOL/mA
Figure 4. Typical VOL vs. IOL for High Drive Enabled Pad (VDD = 5 V)
VOL vs IOL at VDD = 3.0 V, High Drive
350 300 250 -40C 0C 25C 70C 95C 125C 135C
VDD/mV
200 150 100 50 0 0.2 0.3 0.4 0.5 0.6 2 2.5 3 3.5 4
IOL/mA
Figure 5. Typical VOL vs. IOL for High Drive Enabled Pad (VDD = 3 V)
MC9S08SE8 Series MCU Data Sheet, Rev. 3 12 Freescale Semiconductor
Electrical Characteristics
VOL vs IOL at VDD = 5.0 V, Low Drive
600 500 400
-40C 0C 25C 70C 95C 125C
VDD/mV
300 200 100 0 0.2 0.3 0.4 0.5 0.6 1 1.5 2 2.5 3
135C
IOL/mA
Figure 6. Typical VOL vs. IOL for Low Drive Enabled Pad (VDD = 5 V)
VOL vs IOL at VDD = 3.0 V, Low Drive
250 -40C 200 150 100 50 0 160 200 240 280 320 400 500 600 700 800 0C 25C
VDD/mV
70C 95C 125C 135C
IOL/mA
Figure 7. Typical VOL vs. IOL for Low Drive Enabled Pad (VDD = 3 V)
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 13
Electrical Characteristics
VOH vs IOH at VDD = 5.0 V, High Drive
5.1 5 4.9 4.8 4.7 4.6 4.5 4.4 4.3 4.2 4.1 -1 -1.5 -2 -2.5 -3 -9 -9.5 -10 -10.5 -11
-40C 0C 25C 70C 95C 125C 135C
VOH/mV
IOH/mA
Figure 8. Typical VOH vs. IOH for High Drive Enabled Pad (VDD = 5 V)
VOH vs IOL at VDD = 3.0 V, High Drive
3.05 3 2.95 2.9 2.85 2.8 2.75 2.7 2.65 2.6 2.55 2.5 -200 -300 -400 -500 -600 -2 -2.5 -3 -3.5 -4
-40C 0C 25C 70C 95C 125C 135C
VOH/mV
IOH/mA
Figure 9. Typical VOH vs. IOH for High Drive Enabled Pad (VDD = 3 V)
MC9S08SE8 Series MCU Data Sheet, Rev. 3 14 Freescale Semiconductor
Electrical Characteristics
VOH vs IOH at VDD = 5.0 V, Low Drive
5.2 5 4.8
-40C 0C 25C 70C 95C 125C 135C
VOH/mV
4.6 4.4 4.2 4 3.8 -200 -300 -400 -500 -600 -1 -1.5 -2 -2.5 -3
IOH/mA
Figure 10. Typical VOH vs. IOH for Low Drive Enabled Pad (VDD = 5 V)
VOH vs IOH at VDD = 3.0 V, Low Drive
3 2.95 2.9 2.85
-40C 0C 25C 70C 95C 125C 135C
VOH/mV
2.8 2.75 2.7 2.65 2.6 2.55 -160 -200 -240 -280 -320 -400 -500 -600 -700 -800
IOH/mA
Figure 11. Typical VOH vs. IOH for Low Drive Enabled Pad (VDD = 3 V)
3.6
Supply Current Characteristics
This section includes information about power supply current in various operating modes.
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 15
Electrical Characteristics
Table 8. Supply Current Characteristics
Num C Parameter Run supply current measured at (CPU clock = 4 MHz, fBus = 2 MHz) Run supply current measured at (CPU clock = 20 MHz, fBus = 10 MHz) Wait supply current measured at fBus = 2 MHz
2 2
Symbol
VDD (V) 5 3 5 3 5 3
Typical1 2.4 2.18 6.35 5.79 1.4 1.36 1.4
Max 2.72 2.26 7.29 6.42 1.56 1.53 19 28 45.8 15 22 37.2 23 43 76.1 19 38 66.4 500 500 500 500 180 160 8
Unit
Temp (C) -40 to 125
2
1
C
RIDD RIDD WIDD
mA
2
P
mA
-40 to 125
3
P
mA
-40 to 125 -40 to 85 -40 to 105 -40 to 125 -40 to 85 -40 to 105 -40 to 125 -40 to 85 -40 to 105 -40 to 125 -40 to 85 -40 to 105 -40 to 125 -40 to 85 -40 to 125 -40 to 85 -40 to 125 -40 to 125 -40 to 125 -40 to 125
5 4 P Stop2 mode supply current S2IDD 3
A
1.3
A
5 5 P Stop3 mode supply current S3IDD 3 5 6 P RTC adder to stop2 or stop33 S23IDDRTI 3 7 8
1
1.61
A
1.44
A
300 300 122 110 5
nA nA A A A
C C
LVD adder to stop3 (LVDE = LVDSE = 1) Adder to stop3 for oscillator enabled4 (OSCSTEN =1)
S3IDDLVD S3IDDOSC
5 3 5,3
Typical values are based on characterization data at 25 C unless otherwise stated. See Figure 12 through Figure 13 for typical curves across voltage/temperature. 2 All modules except ADC active, ICS configured for FBE, and does not include any dc loads on port pins. 3 Most customers are expected to find that auto-wakeup from stop2 or stop3 can be used instead of the higher current wait mode. Wait mode typical is 220 A at 5 V with fBus = 1 MHz. 4 Values given under the following conditions: low range operation (RANGE = 0) with a 32.768 kHz crystal and low power mode (HGO = 0).
MC9S08SE8 Series MCU Data Sheet, Rev. 3 16 Freescale Semiconductor
Electrical Characteristics
Run IDD at 10 MHz vs Temp
8 7 6 5.5V RIDD (mA) 5 4 3 2 1 0 -40C 0C 25C 70C Temp (C) 95C 125C 135C 5.0V 4.5V 3.3V 3.0V 2.7V
Figure 12. Typical Run IDD Curves
Stop2 IDD vs Temp
20 18 16 14 S2IDD (uA) 12 10 8 6 4 2 0 -40C 0C 25C 70C Temp (C) 95C 125C 135C 5.5V 5.0V 4.5V 3.3V 3.0V 2.7V
Figure 13. Typical Stop2 IDD Curves
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 17
Electrical Characteristics
Stop3 IDD vs Temp
35 30 25 S3IDD (uA) 20 15 10 5 0 -40C 0C 25C 70C Temp (C) 95C 125C 135C
5.5V 5.0V 4.5V 3.3V 3.0V 2.7V
Figure 14. Typical Stop3 IDD Curves
MC9S08SE8 Series MCU Data Sheet, Rev. 3 18 Freescale Semiconductor
Electrical Characteristics
3.7
Num C
External Oscillator (XOSC) Characteristics
Table 9. XOSCVLP Specifications (Temperature Range = -40 to 125C Ambient)
Characteristic Symbol Min. Typical1 Max. Unit
1
Oscillator crystal or resonator (EREFS = 1, ERCLKEN = 1) Low range (RANGE = 0) C High range (RANGE = 1), high gain (HGO = 1), FBELP mode High range (RANGE = 1), low power (HGO = 0), FBELP mode Load capacitors Low range (RANGE=0), low power (HGO = 0) Other oscillator settings
flo fhi fhi C1,C2
32 1 1
-- -- --
38.4 16 8
kHz MHz MHz
2
D
See Note 2 See Note 3
3
Feedback resistor Low range, low power (RANGE = 0, HGO = 0)2 D Low range, high gain (RANGE = 0, HGO = 1) High range (RANGE = 1, HGO = X) Series resistor -- Low range, low power (RANGE = 0, HGO = 0)2 Low range, high gain (RANGE = 0, HGO = 1) High range, low power (RANGE = 1, HGO = 0) D High range, high gain (RANGE = 1, HGO = 1) 8 MHz 4 MHz 1 MHz Crystal start-up time4 Low range, low power Low range, high gain C High range, low power High range, high gain Square wave input clock frequency (EREFS = 0, ERCLKEN = 1) FEE mode D FBE or FBELP mode
t t
RF
-- -- -- -- -- -- -- -- -- -- -- -- --
-- 10 1 -- 100 0 0 0 0 600 400 5 15
-- -- -- -- -- -- 0 10 20 -- -- -- --
M
4
RS
k
CSTL
5
ms
CSTH
6
1 2
fextal
0.03125 0
-- --
20 20
MHz MHz
Data in Typical column was characterized at 3.0 V, 25 C or is typical recommended value. Load capacitors (C1,C2), feedback resistor (RF) and series resistor (RS) are incorporated internally when RANGE = HGO = 0. 3 See crystal or resonator manufacturer's recommendation. 4 Proper PC board layout procedures must be followed to achieve specifications.
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 19
Electrical Characteristics
XOSCVLP EXTAL XTAL RS
RF
C1
Crystal or Resonator C2
Figure 15. Typical Crystal or Resonator Circuit: High Range and Low Range/High Gain
XOSCVLP EXTAL XTAL
Crystal or Resonator
Figure 16. Typical Crystal or Resonator Circuit: Low Range/Low Power
3.8
Num 1 2 3 4 5 6
Internal Clock Source (ICS) Characteristics
Table 10. ICS Frequency Specifications (Temperature Range = -40 to 85C Ambient)
C P P T D Characteristic Average internal reference frequency -- factory trimmed at VDD = 5 V and temperature = 25 C Internal reference frequency -- user trimmed Internal reference start-up time DCO output frequency range -- trimmed2 Low range (DRS = 00) Symbol fint_t fint_ut tIRST fdco_t fdco_DMX32 fdco_res_t Min. -- 31.25 -- 16 -- -- Typical1 39.0625 -- 60 -- 59.77 0.1 Max. -- 39.06 100 20 -- 0.2 Unit kHz kHz s MHz MHz %fdco
2 D DCO output frequency Reference = 32768 Hz and DMX32 = 1
C
Resolution of trimmed DCO output frequency at fixed voltage and temperature (using FTRIM)
MC9S08SE8 Series MCU Data Sheet, Rev. 3 20 Freescale Semiconductor
Electrical Characteristics
Table 10. ICS Frequency Specifications (Temperature Range = -40 to 85C Ambient) (continued)
Num 7 C C Characteristic Resolution of trimmed DCO output frequency at fixed voltage and temperature (not using FTRIM) Total deviation of DCO output from trimmed frequency3 Over full voltage and temperature range Over fixed voltage and temperature range of 0 to 70 C Symbol fdco_res_t fdco_t tAcquire CJitter Min. -- Typical1 0.2 Max. 0.4 Unit %fdco
8 10 11
1 2
C
-- -- --
-1.0 to 0.5 0.5 -- 0.02
2 1 1 0.2
%fdco ms %fdco
C FLL acquisition time4 C Long term jitter of DCO output clock (averaged over 2-ms interval)5
Data in Typical column was characterized at 3.0 V, 25 C or is typical recommended value. The resulting bus clock frequency should not exceed the maximum specified bus clock frequency of the device. 3 This parameter is characterized and not tested on each device. 4 This specification applies to any time the FLL reference source or reference divider is changed, trim value changed or changing from FLL disabled (FBELP, FBILP) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running. 5 Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f Bus. Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise injected into the FLL circuitry via VDD and VSS and variation in crystal oscillator frequency increase the CJitter percentage for a given interval.
1.00%
0.50%
0.00% Deviation (%) -60 -40 -20 -0.50% 0 20 40 60 80 100 120
-1.00%
TBD
Temperature
-1.50%
-2.00%
Figure 17. Deviation of DCO Output from Trimmed Frequency (20 MHz, 3.0 V)
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 21
Electrical Characteristics
3.9
ADC Characteristics
Table 11. 10-Bit ADC Operating Conditions
Characteristic Conditions Absolute Symb VDDA VDDA VSSA VADIN CADIN RADIN 10-bit mode fADCK > 4MHz fADCK < 4MHz 8-bit mode (all valid fADCK) Min 2.7 -100 -100 VREFL -- -- -- -- -- 0.4 fADCK 0.4 Typ1 -- 0 0 -- 4.5 3 -- -- -- -- -- Max 5.5 100 100 VREFH 5.5 5 5 10 10 8.0 MHz 4.0 Unit V mV mV V pF k Comment
Supply voltage Ground voltage Input voltage Input capacitance Input resistance
Delta to VDD (VDD - VDDA)2 Delta to VSS (VSS - VSSA)2
Analog source resistance
RAS
k
External to MCU
ADC conversion clock frequency
1
High speed (ADLPC = 0) Low power (ADLPC = 1)
Typical values assume VDDA = 5.0 V, Temp = 25 C, fADCK = 1.0 MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 2 DC potential difference.
SIMPLIFIED INPUT PIN EQUIVALENT CIRCUIT ZAS RAS VADIN VAS Pad leakage due to input protection
ZADIN SIMPLIFIED CHANNEL SELECT CIRCUIT RADIN
ADC SAR ENGINE
+ -
+ -
CAS
RADIN INPUT PIN
RADIN
INPUT PIN
RADIN CADIN
INPUT PIN
Figure 18. ADC Input Impedance Equivalency Diagram
MC9S08SE8 Series MCU Data Sheet, Rev. 3 22 Freescale Semiconductor
Electrical Characteristics
Table 12. 10-Bit ADC Characteristics (VREFH = VDDA, VREFL = VSSA)
Characteristic Supply Current ADLPC = 1 ADLSMP = 1 ADCO = 1 Supply Current ADLPC = 1 ADLSMP = 0 ADCO = 1 Supply Current ADLPC = 0 ADLSMP = 1 ADCO = 1 Supply Current ADLPC = 0 ADLSMP = 0 ADCO = 1 Supply Current ADC Asynchronous Clock Source Conversion Time (Including sample time) Stop, Reset, Module Off High Speed (ADLPC = 0) D Low Power (ADLPC = 1) Short Sample (ADLSMP = 0) Long Sample (ADLSMP = 1) Short Sample (ADLSMP = 0) Long Sample (ADLSMP = 1) Temp Sensor Slope Temp Sensor Voltage -40C- 25C D 25C- 125C 25C D VTEMP25 m -- -- 3.638 1.396 -- -- mV fADACK Conditions C Symb Min Typ1 Max Unit Comment
T
IDDA
--
133
--
A
T
IDDA
--
218
--
A
T
IDDA
--
327
--
A
D
IDDA
--
0.582
1
mA
D
IDDA
-- 2 1.25 --
0.011 3.3 2 20 40 3.5 23.5 3.266
1 5
A MHz tADACK = 1/fADACK
3.3 -- -- -- -- -- mV/C ADCK cycles ADCK cycles
D
tADC -- --
Sample Time
D
tADS -- --
See SE8 reference manual for conversion time variances
Characteristics for 28-pin packages only Total Unadjusted Error Differential Non-Linearity Integral Non-Linearity 10-bit mode 8-bit mode 10-bit mode2 8-bit mode3 P P P DNL P T INL 8-bit mode T -- -- -- ETUE -- -- -- 1 0.5 0.5 0.3 0.5 0.3 2.5 1.0 1.0 0.5 1.0 0.5 LSB3 Includes quantization
LSB3
10-bit mode
LSB3
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 23
Electrical Characteristics
Table 12. 10-Bit ADC Characteristics (VREFH = VDDA, VREFL = VSSA) (continued)
Characteristic Zero-Scale Error Full-Scale Error Quantization Error Input Leakage Error Conditions 10-bit mode 8-bit mode 10-bit mode 8-bit mode 10-bit mode D 8-bit mode 10-bit mode D 8-bit mode EIL EQ C P P T T EFS EZS Symb Min -- -- -- -- -- -- -- -- Typ1 0.5 0.5 0.5 0.5 -- -- 0.2 0.1 Max 1.5 0.5 1 0.5 0.5 0.5 2.5 1 Unit LSB3 Comment VADIN = VSSA
LSB3
VADIN = VDDA
LSB3 Pad leakage4 * RAS
LSB3
Characteristics for 16-pin package only Total Unadjusted Error Differential Non-Linearity Integral Non-Linearity Zero-Scale Error Full-Scale Error Quantization Error Input Leakage Error
1
10-bit mode 8-bit mode 10-bit mode3 8-bit mode3
P P P DNL P T INL T P P T T D EFS EZS ETUE
-- -- -- -- -- -- -- -- -- -- -- EQ -- --
1.5 0.7 0.5 0.3 0.5 0.3 1.5 0.5 1 0.5 -- -- 0.2 0.1
3.5 1.5 1.0 0.5 1.0 0.5 2.1 0.7 1.5 0.5 0.5 0.5 2.5 1 LSB3
Includes quantization
LSB3
10-bit mode 8-bit mode 10-bit mode 8-bit mode 10-bit mode 8-bit mode 10-bit mode 8-bit mode 10-bit mode
LSB3
LSB3
VADIN = VSSA
LSB3
VADIN = VDDA
LSB3 Pad leakage4 * RAS
D 8-bit mode
EIL
LSB3
--
Typical values assume VDDA = 5.0 V, Temp = 25 C, fADCK = 1.0 MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 2 Monotonicity and No-Missing-Codes guaranteed in 10-bit and 8-bit modes 3 1 LSB =(V N REFH - VREFL)/2 4 Based on input pad leakage current. Refer to pad electricals.
MC9S08SE8 Series MCU Data Sheet, Rev. 3 24 Freescale Semiconductor
Electrical Characteristics
3.10
AC Characteristics
This section describes ac timing characteristics for each peripheral system.
3.10.1
Num 1 2 3 4 5 6 C D D D D D D
Control Timing
Table 13. Control Timing
Rating Bus frequency (tcyc = 1/fBus) Internal low power oscillator period External reset pulse width2 Reset low drive3 Symbol fBus tLPO textrst trstdrv tMSSU tMSH Min DC 700 100 34 x tcyc 500 100 Typical1 -- -- -- -- -- -- Max 10 1300 -- -- -- -- Unit MHz s ns ns ns s
BKGD/MS setup time after issuing background debug force reset to enter user or BDM modes BKGD/MS hold time after issuing background debug force reset to enter user or BDM modes4 IRQ pulse width Asynchronous path2 Synchronous path5 Pin interrupt pulse width Asynchronous path2 Synchronous path5 Port rise and fall time -- Low output drive (PTxDS = 0) (load = 50 pF)6 Slew rate control disabled (PTxSE = 0) Slew rate control enabled (PTxSE = 1)
7
D
tILIH, tIHIL
100 1.5 x tcyc 100 1.5 x tcyc --
--
--
ns
8
D
tILIH, tIHIL
--
--
ns
tRise, tFall
9
40 75
--
ns
C
Port rise and fall time -- High output drive (PTxDS = 1) (load = 50 pF) Slew rate control disabled (PTxSE = 0) Slew rate control enabled (PTxSE = 1)
tRise, tFall
--
11 35
--
ns
1 2 3 4 5 6
Typical values are based on characterization data at VDD = 5.0 V, 25 C unless otherwise stated. This is the shortest pulse that is guaranteed to be recognized as a reset pin request. Shorter pulses are not guaranteed to override reset requests from internal sources. When any reset is initiated, internal circuitry drives the reset pin (if enabled, RSTPE = 1) low for about 34 cycles of tcyc. To enter BDM mode following a POR, BKGD/MS should be held low during the power-up and for a hold time of tMSH after VDD rises above VLVD. This is the minimum pulse width that is guaranteed to pass through the pin synchronization circuitry. Shorter pulses may or may not be recognized. In stop mode, the synchronizer is bypassed so shorter pulses can be recognized in that case. Timing is shown with respect to 20% VDD and 80% VDD levels. Temperature range -40 C to 125 C.
textrst RESET PIN
Figure 19. Reset Timing
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 25
Electrical Characteristics
tIHIL IRQ/Pin Interrupts
IRQ/Pin Interrupts tILIH
Figure 20. IRQ/Pin Interrupt Timing
3.10.2
TPM/MTIM Module Timing
Synchronizer circuits determine the shortest input pulses that can be recognized or the fastest clock that can be used as the optional external source to the timer counter. These synchronizers operate from the current bus rate clock.
Table 14. TPM Input Timing
Num 1 2 3 4 5 C D D D D D Rating External clock frequency External clock period External clock high time External clock low time Input capture pulse width Symbol fTPMext tTPMext tclkh tclkl tICPW Min DC 4 1.5 1.5 1.5 Max fBus/4 -- -- -- -- Unit MHz tcyc tcyc tcyc tcyc
tTCLK tclkh
TCLK tclkl
Figure 21. Timer External Clock
tICPW TPMCHn
TPMCHn tICPW
Figure 22. Timer Input Capture Pulse
MC9S08SE8 Series MCU Data Sheet, Rev. 3 26 Freescale Semiconductor
Ordering Information
3.11
Flash Specifications
This section provides details about program/erase times and program-erase endurance for the flash memory. Program and erase operations do not require any special power sources other than the normal VDD supply. For more detailed information about program/erase operations, see the Memory section in the reference manual.
Table 15. Flash Characteristics
Num 1 2 3 4 5 6 7 8 9 10
1 2
C D D D D P P P P C C
Characteristic Supply voltage for program/erase Supply voltage for read operation Internal FCLK frequency
1
Symbol Vprog/erase VRead fFCLK tFcyc tprog tBurst tPage tMass nFLPE tD_ret location)2
Min 2.7 2.7 150 5
Typical -- -- -- -- 9 4 4000 20,000
Max 5.5 5.5 200 6.67
Unit V V kHz s tFcyc tFcyc tFcyc tFcyc
Internal FCLK period (1/FCLK) Byte program time (random Byte program time (burst Page erase Mass erase time2 time2 endurance3 mode)2
Program/erase TL to TH = -40 C to 125 C T = 25 C Data retention4
10,000 15
-- 100,000 100
-- --
cycles years
The frequency of this clock is controlled by a software setting. These values are hardware state machine controlled. User code does not need to count cycles. This information supplied for calculating approximate time to program and erase. 3 Typical endurance for flash was evaluated for this product family on the 9S12Dx64. For additional information on how Freescale defines typical endurance, please refer to Engineering Bulletin EB619/D, Typical Endurance for Nonvolatile Memory. 4 Typical data retention values are based on intrinsic capability of the technology measured at high temperature and de-rated to 25 C using the Arrhenius equation. For additional information on how Freescale defines typical data retention, please refer to Engineering Bulletin EB618/D, Typical Data Retention for Nonvolatile Memory.
4
Ordering Information
This chapter contains ordering information for the device numbering system. Example of the device numbering system:
MC 9 S08 SE 8 C XX E Status (MC = Fully Qualified) Memory (9 = Flash-based) Core Family RoHS compliance indicator (E = yes) Package designator (see Table 16) Temperature range (C = -40 C to 85 C) (V = -40 C to 105 C) (M = -40 C to 125 C) Memory Size (in KB)
MC9S08SE8 Series MCU Data Sheet, Rev. 3 Freescale Semiconductor 27
Ordering Information
4.1
Package Information
Table 16. Package Descriptions
Pin Count 28 28 16
Package Type Plastic Dual In-line Pin Small Outline Integrated Circuit Thin Shrink Small Outline Package
Abbreviation PDIP SOIC TSSOP
Designator RL WL TG
Case No. 710 751F 948F
Document No. 98ASB42390B 98ASB42345B 98ASH70247A
4.2
Mechanical Drawings
The following pages are mechanical drawings for the packages described in Table 16.
MC9S08SE8 Series MCU Data Sheet, Rev. 3 28 Freescale Semiconductor
How to Reach Us:
Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com
Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale's Environmental Products program, go to http://www.freescale.com/epp. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc. 2008-2009. All rights reserved.
Document Number: MC9S08SE8 Rev. 3 4/2009

▲Up To Search▲

Price & Availability of MC9S08SE8

	To Download MC9S08SE8 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .